Wood stove install

This is a catch all off topic forum to talk about anything not covered by other sections.
Post Reply
User avatar
Red Squirrel
Posts: 29210
Joined: Wed Dec 18, 2002 12:14 am
Location: Northern Ontario
Contact:

Wood stove install

Post by Red Squirrel »

Couple years back my Embridge gas bill skyrocketed and I decided to get a wood stove. Trudeau's carbon tax sure doesn't help either. After not being able to find anyone to install it and just being given the run around I decided to do it myself. Figured I'd share the process.
IMG_20221113_141835.jpg
IMG_20221113_141835.jpg (1.34 MiB) Viewed 4789 times
Bought it at Canadian Tire, it's an Englander 15-w06. Had fun transporting it to the basement, needed help for that one!

IMG_20221107_233026.jpg
IMG_20221107_233026.jpg (2.02 MiB) Viewed 4789 times
This is location where it went. Had some work to do to make it suitable such as adding cement board, finishing walls, etc.

IMG_20230111_190437.jpg
IMG_20230111_190437.jpg (1.65 MiB) Viewed 4789 times
IMG_20230113_205809.jpg
IMG_20230113_205809.jpg (2.02 MiB) Viewed 4789 times
IMG_20230212_183636.jpg
IMG_20230212_183636.jpg (1.71 MiB) Viewed 4789 times
Lots of work had to be done above, such as moving my outside garden hose, as ceiling is to be covered with cement board and I really don't like idea of inaccessible plumbing. Also moved a bunch of electrical to clean up that ceiling area as I also wanted to add a 6" vent intake pipe that I will connect to a fan later down the road.

IMG_20230413_210318.jpg
IMG_20230413_210318.jpg (1.68 MiB) Viewed 4789 times
Walls mostly done, and ceiling done. That pipe in the corner is a fresh air intake.

IMG_20230510_143645.jpg
IMG_20230510_143645.jpg (1.42 MiB) Viewed 4789 times
Fresh air intake covered.

IMG_20230524_021948.jpg
IMG_20230524_021948.jpg (2.58 MiB) Viewed 4789 times
Tiles all done, and also added thinset to all the cementboard seams. Also eliminated an ethernet jack since I accidentally cut the wiring and realized it was easier to just eliminate it completely. There is another on the other side anyway. I may use this for automation stuff in the future. All those outlets are a bit on the redundant side but they were added well before I planned to put a wood stove there so they stay.

At this point we were in May 2023. Decided to take a break for the summer as I was still hoping to find someone to do my chimney. Had someone start then never finish the job so did end up doing it myself.


IMG_20231102_162324.jpg
IMG_20231102_162324.jpg (1.44 MiB) Viewed 4789 times
In November 2023 I started working on the basement again, won't go over the details of this part of the project, but I wanted to wall in my server room so I did. This was always planned either way, but now was the time to do it.

IMG_20231111_005945.jpg
IMG_20231111_005945.jpg (1.76 MiB) Viewed 4789 times
IMG_20231118_190132.jpg
IMG_20231118_190132.jpg (1.69 MiB) Viewed 4789 times
IMG_20231122_125401.jpg
IMG_20231122_125401.jpg (2.37 MiB) Viewed 4789 times
IMG_20231203_190135.jpg
IMG_20231203_190135.jpg (1.35 MiB) Viewed 4789 times
IMG_20231226_211912.jpg
IMG_20231226_211912.jpg (2.06 MiB) Viewed 4789 times
Stove now moved in it's proper location. This was end of 2023.

IMG_20240105_194312.jpg
IMG_20240105_194312.jpg (1.87 MiB) Viewed 4789 times
Stove pipe staged

At this point I had to do the chimney but it was winter so decided to wait until summer. I did lot of other work in the basement such as drywalling the rest of the side where wood stove is.

IMG_20240829_172659.jpg
IMG_20240829_172659.jpg (1019.66 KiB) Viewed 4789 times
Opened up soffit to start prepping the hole for the chimney to go through.

IMG_20240909_163133.jpg
IMG_20240909_163133.jpg (1.99 MiB) Viewed 4789 times
Chimney going through soffit.

IMG_20240910_195545.jpg
IMG_20240910_195545.jpg (2.42 MiB) Viewed 4789 times
I was debating on whether or not I should go higher at this point as it needs to be 2 feet higher than the highest point of roof within 10 feet and I was kind of borderline. Opted to go for another 3' length since I had it anyway.

IMG_20240910_200308.jpg
IMG_20240910_200308.jpg (1.55 MiB) Viewed 4789 times
IMG_20240916_115152.jpg
IMG_20240916_115152.jpg (705.56 KiB) Viewed 4789 times
Got the whole setup WETT inspected and passed with flying colours, am pretty nappy! Still need to close up the soffit but other than that the stove is ready.

IMG_20240916_151258.jpg
IMG_20240916_151258.jpg (1.25 MiB) Viewed 4789 times
First fire! This is a small kindling fire to break it in. There is another break in fire to do that is slightly bigger but will do that when it's colder out. It was +30 out when I did this, I just couldn't wait!

Overall this install was more complex and involved than I anticipated especially as I originally wanted to hire it out but couldn't find anyone to do it. Probably would not have taken nearly 2 years had I just opted to do it myself right away though, as I spent a lot of time waiting for people to call me back who never did.

Looking forward to using it throughout the winter as I will save a lot on natural gas. Normally I try to keep the house cool to save on gas and suffer a little because of it, now I don't have to do that.
Honk if you love Jesus, text if you want to meet Him!
drmrlordx
Posts: 8
Joined: Sat Feb 10, 2024 8:47 am

Re: Wood stove install

Post by drmrlordx »

Nicely done. How much is natgas per therm where you live?
User avatar
Red Squirrel
Posts: 29210
Joined: Wed Dec 18, 2002 12:14 am
Location: Northern Ontario
Contact:

Re: Wood stove install

Post by Red Squirrel »

According to the Enbridge site it's 13.6488 cents/cubic metre but there's a bunch of extra fees and taxes as well so it's hard to tell for sure what it comes up to or if those are included, they're not really clear. My typical bill last year was $170/mo, this year it's been adjusted down to $100 and I had a bunch of freebie months throughout the summer, since I replaced my water heater with a heat pump one so I hardly used any gas at all. I presume I'll get my bill down even lower with the wood stove.

I don't think I have enough wood for the whole winter so will still end up using the furnace but will use it way less. Especially on the days where it's a little cold where I just want a bit of heat to take the edge off, I can do a quick fire and let it burn out.

From what I've learned through using the wood stove a few times already though is that I will definitely want to run ductwork with a blower so I can move the heat to the main part of the house, as right now it just stays mostly where the stove is. I was already planing on doing that anyway but was going to get a feel for it first before I do it.
Honk if you love Jesus, text if you want to meet Him!
drmrlordx
Posts: 8
Joined: Sat Feb 10, 2024 8:47 am

Re: Wood stove install

Post by drmrlordx »

Is that in CAD? $170 CAD/month isn't awful. But if it was cheaper before then it makes sense to want to get away from it, even though it's kinda funny that you went from burning natgas to . . . wood. Considering WHY natgas is getting so expensive.
User avatar
Red Squirrel
Posts: 29210
Joined: Wed Dec 18, 2002 12:14 am
Location: Northern Ontario
Contact:

Re: Wood stove install

Post by Red Squirrel »

Yeah the fact that it went up that high, and will probably keep going up, is what made me give in. The wood is going to be relatively free other than gas for my truck to go get it.

My next step is to start incorporating solar more into my house as well, since hydro is another cost that I could work on reducing a bit.
Honk if you love Jesus, text if you want to meet Him!
Post Reply